direct loaded...
i have only 1 hotend connected, but FW has both enabled...
no temp error? value shows -14
might be that check loop is disabled
thermistor tables?
i see you left stock ones stock marlin ones (i presume you use differnt than stock)
i tried inserting thermistor table 14 (from rc3, gave me good results), but i keep hitting walls
compile report(from my port not yours):
In file included from sketch\Marlin_main.cpp:250:0:
temperature.h:55: error: expected '}' before 'enum'
enum ADCSensorState {
^
temperature.h:55: error: expected ',' or ';' before 'enum'
In file included from sketch\MarlinConfig.h:37:0,
from sketch\Marlin.h:36,
from sketch\Marlin_main.cpp:244:
sketch\Marlin_main.cpp: In function 'void gcode_M301()':
temperature.h:97: error: 'SensorsReady' was not declared in this scope
#define ACTUAL_ADC_SAMPLES max(int(MIN_ADC_ISR_LOOPS), int(SensorsReady))
^
C:\Users\marko\AppData\Local\Arduino15\packages\arduino\hardware\avr\1.6.20\cores\arduino/Arduino.h:93:24: note: in definition of macro 'max'
#define max(a,b) ((a)>(b)?(a):(b))
^
sketch\temperature.h:128:45: note: in expansion of macro 'ACTUAL_ADC_SAMPLES'
#define PID_dT ((OVERSAMPLENR * float(ACTUAL_ADC_SAMPLES)) / (F_CPU / 64.0 / 256.0))
^
sketch\temperature.h:152:39: note: in expansion of macro 'PID_dT'
#define scalePID_i(i) ( (i) * PID_dT )
^
sketch\Marlin_main.cpp:8961:48: note: in expansion of macro 'scalePID_i'
if (parser.seen('I')) PID_PARAM(Ki, e) = scalePID_i(parser.value_float());
^
temperature.h:97: error: 'SensorsReady' was not declared in this scope
#define ACTUAL_ADC_SAMPLES max(int(MIN_ADC_ISR_LOOPS), int(SensorsReady))
^
C:\Users\marko\AppData\Local\Arduino15\packages\arduino\hardware\avr\1.6.20\cores\arduino/Arduino.h:93:24: note: in definition of macro 'max'
#define max(a,b) ((a)>(b)?(a):(b))
^
sketch\temperature.h:128:45: note: in expansion of macro 'ACTUAL_ADC_SAMPLES'
#define PID_dT ((OVERSAMPLENR * float(ACTUAL_ADC_SAMPLES)) / (F_CPU / 64.0 / 256.0))
^
sketch\temperature.h:154:39: note: in expansion of macro 'PID_dT'
#define scalePID_d(d) ( (d) / PID_dT )
^
sketch\Marlin_main.cpp:8962:48: note: in expansion of macro 'scalePID_d'
if (parser.seen('D')) PID_PARAM(Kd, e) = scalePID_d(parser.value_float());
^
In file included from sketch\Marlin.h:46:0,
from sketch\Marlin_main.cpp:244:
temperature.h:97: error: 'SensorsReady' was not declared in this scope
#define ACTUAL_ADC_SAMPLES max(int(MIN_ADC_ISR_LOOPS), int(SensorsReady))
^
sketch\serial.h:52:76: note: in definition of macro 'SERIAL_PROTOCOLPAIR'
#define SERIAL_PROTOCOLPAIR(name, value) (serial_echopair_P(PSTR(name),(value)))
^
sketch\Marlin_main.cpp:8975:7: note: in expansion of macro 'SERIAL_ECHOPAIR'
SERIAL_ECHOPAIR(" i:", unscalePID_i(PID_PARAM(Ki, e)));
^
sketch\temperature.h:97:28: note: in expansion of macro 'max'
#define ACTUAL_ADC_SAMPLES max(int(MIN_ADC_ISR_LOOPS), int(SensorsReady))
^
sketch\temperature.h:128:45: note: in expansion of macro 'ACTUAL_ADC_SAMPLES'
#define PID_dT ((OVERSAMPLENR * float(ACTUAL_ADC_SAMPLES)) / (F_CPU / 64.0 / 256.0))
^
sketch\temperature.h:153:39: note: in expansion of macro 'PID_dT'
#define unscalePID_i(i) ( (i) / PID_dT )
^
sketch\Marlin_main.cpp:8975:30: note: in expansion of macro 'unscalePID_i'
SERIAL_ECHOPAIR(" i:", unscalePID_i(PID_PARAM(Ki, e)));
^
Multiple libraries were found for "LiquidCrystal.h"
Used: C:\Users\marko\Documents\Arduino\libraries\LiquidCrystal
Not used: C:\Program Files (x86)\Arduino\libraries\LiquidCrystal
exit status 1
expected '}' before 'enum'
other than that
board should be now 74/75 instead of 7
LCD menu, no delta calibration menu...
i presume it reflects your setup, since rods are set to 200
it would be nice to colaborate on some addon options, that some people use and include it in final community version....
i see many use extra light, why not have some options in LCD menu:
off, on, auto(let SW control it over predefined pin) for simple light
i reckon whatever we come up with, will be final version for this printer...
since there was no HW updates and refreshed verson is closed sorce.
